云南快乐十分玩法介绍

New Light Standard Design... I hope...

ninj

Printing Ninja
Joined
Dec 28, 2011
Messages
82
Reaction score
99
Points
83
In my case wild temperature fluctuations were caused by the heater cartridge and thermister working loose and moving around during fast head movements.
 

stratman

Printer VIP
Platinum Printer Member
Joined
Apr 19, 2007
Messages
6,584
Reaction score
4,690
Points
373
Location
USA
Printer Model
Canon MB5120, Pencil
What's a PID calibration... ?
Pelvic Inflammatory Disease? :idunno

Where has your printer been? Better get it up in stirrups for a look see.


The following has instruction for PID tuning. So easy a kid can do it. ;)

Disregard the giveaway crap at the beginning. There are more videos on YouTube about this made by adults for different printers / software.

 

Nifty

Printer Master
Administrator
Joined
Nov 3, 2004
Messages
2,606
Reaction score
923
Points
297
Location
Bay Area CA
Printer Model
CR-10, i560 ,MFC-7440N
Ciara came through here this morning without a taught and flattened the lamp standard, the base gave way and it caused the lamp to wobble at the bottom which broke the top off
ugh, sorry to hear this!
I reckon the CR-10 printer will have to cancelled its well-deserved rest and preform the same task once again.
well, that's a silver lining, no?

I definitely haven't been printing as much as I would like lately. Maybe I need something to break?
 

PeterBJ

Printer VIP
Platinum Printer Member
Joined
Nov 27, 2010
Messages
4,155
Reaction score
3,532
Points
343
Location
Copenhagen Denmark
Printer Model
Canon iP4300 + Epson scanner
More . It is the most precise type of controller, but can become unstable, for instance causing temperature cycling, if the parameters are set wrongly.
 

The Hat

Printer VIP
Moderator
Joined
Jan 18, 2010
Messages
12,176
Reaction score
5,831
Points
413
Location
Wicklow Ireland
Printer Model
Canon ? + 3D, CR-10.
Thanks guys for the help and encouragement, but when it comes to altering the Firmware on these printers, I like to leave that to those that know what they’re doing.

Because you wouldn’t catch me Frigging around in any printer firmware, I know much easier and quicker ways to kill a motherboard.. I’m firmware illiterate and wish to stay that way, besides I’m still using the original CURA 15.04.6
 

Nifty

Printer Master
Administrator
Joined
Nov 3, 2004
Messages
2,606
Reaction score
923
Points
297
Location
Bay Area CA
Printer Model
CR-10, i560 ,MFC-7440N
Because you wouldn’t catch me Frigging around in any printer firmware, I know much easier and quicker ways to kill a motherboard
Yup, same with me! I'll fiddle around with a lot of the bits on my computer, but I have no interest in messing with the motherboard or firmware!
 

The Hat

Printer VIP
Moderator
Joined
Jan 18, 2010
Messages
12,176
Reaction score
5,831
Points
413
Location
Wicklow Ireland
Printer Model
Canon ? + 3D, CR-10.
Up-date… On the Mark 3..

I’ve come to a crossroads with the Standard Lamp, I got the upright column back in place, and only need to pour the last bit of concrete around the base, hopefully I’ve got it right this time and it won’t suffer the same faith as the previous two did.

I’ve managed to repair the top centre section that got damaged in the fall, it wasn’t easy to matched the two pieces back together again, but it’s finally ready for fitting, I still have to make one new lantern and repair two others, and this is where the bigger CR-10 is needed.

I don’t reckon I can finish the Standard lamp any time soon, maybe mid-April if I’m lucky, because the power supply for the CR-10 is still in cloud cuckoo land and the tracking isn’t working, ok it’s only been two weeks but if feel like forever right now..

I can’t start back on any of the upgrades for the CR-10 till I’m finished the Lamp Standard, plus I’m using the Ender-2’s upgrades as a Guinee pig for the CR-10, it’s a toss-up between using two new different types of Linear rails…
 

Latest posts

Top
乐优彩票天天红单下载 乐优彩票登入,备用,官方网址 乐优彩票网址是多少 乐优炫彩app 乐优炫彩app下载 乐优炫彩天天红单 乐优炫彩彩票app下载 乐优炫彩app天天红单 乐体育app下载 乐八彩票邀请码